Tanks

Stainless Steel mixing tank. The hatch is supported by heavy duty pulley wire system for ease of access. The contents of the tank are stirred using a 3 phase motor. The tank is supported on ground via threaded stands. Tank ID: 1300mm Internal volume: 1.13 m3 Working Capacity: 1000L Motor Specs: - Type: MH2-112M4 - 4kW - 1450 rpm - 400V, 8.1A - 50Hz - 3 Phase

This cylindrical, vertical SUS tank was used to mix ingredients in a food manufacturing plant. Power Supply: 415V, 3Ph, 50Hz Capacity: 100L Outlet: sited horizontally at center of tank base. Gear TYP: TN|F5 Ratio: 30/1 with VSD , E-Stop, Stainless Steel control cabinet , Mixer on / off, Safety (Reset, Inbterlock and mointoring) + $4,500 + GST

This 304 Stainless Steel, 200 L, single skin tank, is fitted with a side mounted stirrer, which has 3 blades at the bottom of the shaft, reaching near to the bottom of the tank. It was previously used in a bakery in Australia. The tank has 4 legs, which are mounted on load cells, with a waterproof control panel, mounted within a steel cabinet. There is a central bottom discharge as well a

These twin jacketed premix tanks have a header tank for ingredient addition.They were used in syrup manufacture in a confectionery plant. All are mounted onto a s/s frame.The lower twin tanks are fitted with scraper agitators, heat probes and sieves to filter out particles. Header Tank Capacity:250L Header Tank dimensions:830 mm OD x 470mm D Lower Tank dimensions: 580mm OD x 740mm D (conical

These twin premix tanks were used in syrup manufacture in a confectionery plant. The top tank only is Jacketed They are both mounted onto a s/s frame. Each tank is fitted with scraper agitators, heat probes and sieves to filter out particles. Tank dimensions: 580mm OD x 740mm D (conical outlet) Capacity: Approx 200L each Agitator: Flat bladed impeller. 0.75kW, 50Hz, Ratio: 15:1 *****

- Effective Volume: 1000 Ltr - Total Volume: 1430 Ltr - Material: SUS304 - Material Thickness: 4mm - 80-Degree Conical Base - Upper Reducer: 1.1Kw/49rpm - Lower Reducer: 3Kw/29rpm - 4" Pneumatic Ball Valve, Triclover Fitting - Two (2") x 51mm Diameter Inlets - Comes with 2 Lids, 2 Safety Grids, 4 Legs

Specifications Total Volume: 2,500 Ltr Material Construction: SUS304 Outlet: 4" Butterfly Valve Included Accessories: - 38mm CIP - 2" Inlet - Manhole Dimensions: 1,556 x 1,556 x 2,954 mm (l x w x h)

This brand new s/s IOPAK "cleanskin" holding tank can be used for many purposes! It can be used to simply store a product as it is fitted with half moon lids. Add castors and it becomes a mobile container - or push it under a wall- mounted agitator and it becomes a mixing tank. The STRENGTHENING SECTION, fitted to one side allows you to clamp on an agitator and mix your product with no fu

This brand new s/s IOPAK "cleanskin" holding tank can be used for many purposes! It can be used to simply store a product as it is fitted with a lid. Add castors and it becomes a mobile container - or push it under a wall- mounted agitator and it becomes a mixing tank. The STRENGTHENING SECTION, fitted to one side allows you to clamp on an agitator and mix your product with no fuss. Standard M

This brand new s/s IOPAK "cleanskin" holding tank can be used for many purposes! It can be used to simply store a product as it is fitted with a lid. Add castors and it becomes a mobile container - or push it under a wall- mounted agitator and it becomes a mixing tank. The STRENGTHENING SECTION, fitted to one side allows you to clamp on an agitator and mix your product with no fuss. Standard M

Specifications: Tank Diameter: 2,300 mm Tank Depth: 2,500 mm Overall Height: 3,000 mm Outlet Height from Floor: 250 mm Manhole Diameter: 600 mm Product In/Outlet Diameter: 50 mm (2 inch) CIP Diameter 38mm 304 stainless steel Not Jacketed Electrical: 3 Phase, 415 Volts, 3Kw, 49RPM These are made new to order, with an approx. 3 months lead time.